README-ned-settings

NED settings details

---

This NED is equipped with a number of runtime configuration options "NED settings" allowing for customization by the end user. All options are configurable using the NSO API for NED settings. Most NED settings can be configured globally, per device profile or per device instance in the following locations:

global /ncs:devices/global-settings/ned-settings/cisco-iosxr_nc/ profile /ncs:devices/ncs:profiles/profile:/ned-settings/cisco-iosxr_nc/ device /ncs:/device/devices/device:/ned-settings/cisco-iosxr_nc/

Profiles setting overrides global-settings and device settings override profile settings, hence the narrowest scope of the setting is used by the device.

If user changes a ned-setting, then user must reconnect to the device, i.e. disconnect and connect in order for the new setting to take effect.

From the NSO CLI the device instance NED settings for this NED are available under:

# config
# devices device dev-1 ned-settings cisco-iosxr_nc

Press TAB to see all the NED settings.

Table of contents

---

1. ned-settings cisco-iosxr_nc
2. transaction
   2.1. ignore-rpc-errors
   2.2. extra-get-config-paths
   2.3. exclude-namespaces
   2.4. inject-meta-data
   2.5. inbound
   2.6. outbound
3. connection
   3.1. capabilities
        3.1.1. regex-exclude
        3.1.2. regex-include
        3.1.3. inject
   3.2. ssh
4. proxy
5. live-status
   5.1. regex-exclude
   5.2. cli
        5.2.1. auto-prompts
6. logger
7. developer

1. ned-settings cisco-iosxr_nc

---

This file describes the ned-settings for cisco-iosxr_nc.

2. ned-settings cisco-iosxr_nc transaction

---

Settings affecting different aspects of NSO transactions towards device.

- transaction confirmed-commit enable <true|false> (default true)

  Enables confirmed-commit (if supported by device).


- transaction confirmed-commit confirm-timeout <uint16>

  Timeout in seconds, if set, used as 'confirm-timeout' parameter to the confirmed-commit
  (otherwise defaults to 600 seconds).


- transaction confirmed-commit persisted <true|false> (default false)

  Enable this setting to use the 'persist-id' to let confirming commit be done in other session
  (e.g. if closing session between commit and persist phases). NOTE: This can only be used with
  devices which support netconf capability 'confirmed-commit:1.1'.


- transaction validate-before-commit <true|false> (default false)

  If devices supports the validate1.1 capability, the NED will send a validate rpc before
  sending the commit rpc.


- transaction persist-to-startup <true|false> (default true)

  If enabled, 'running' datastore will be copied to 'startup' in NSO persist stage (if device
  supports distinct startup datastore).


- transaction discard-changes-before-lock <true|false> (default false)

  If enabled, and using the 'candidate' datastore, a 'discard-changes' operation will be issued
  before trying to lock 'candidate'.


- transaction lock-running-before-candidate <true|false> (default false)

  If enabled, and using the 'candidate' datastore, the 'running' datastore will also be locked
  during transactions.


- transaction reconnect-on-commit <true|false> (default false)

  If enabled, the NED will reconnect to the device after commit to ensure connectivity is not
  broken (i.e. aborting the NSO commit stage if re-connect fails). This can for example be used
  as an extra safeguard for early detection of invalid config being applied, which leaves the
  device in an unreachable state. When used together with 'confirmed-commit' it will fail the
  commit in NSO, while still leaving it up to the device to rollback the commit (since no
  'confirming' commit will be sent from NSO). For devices that enforces the use of 'persist-id',
  according to RFC, when using 'confirmed-commit' accross sessions, the ned-setting
  'confirmed-commit/persisted' needs to be enabled aswell.


- transaction commit-in-persist <true|false> (default false)

  If enabled, the NED will not send commit until in the persist phase in NSO (like a confirmed
  commit, assuming config has been validated in the prepare or commit phase). Normally the
  commit is sent in the NSO commit phase to be able to abort the transaction if the commit
  fails, since errors reported by device in the persist phase will only lead to an alarm in NSO,
  the transaction can no longer be aborted in the persist phase (i.e. the transaction must be
  aborted in the prepare or commit phases for NSO to be able to rollback properly).


- transaction ignore-rpc-warnings <true|false> (default true)

  By default rpc-error reply with severity 'warning' will not be treated as error, set to
  'false' to treat warnings as errors (i.e. abort transaction on warnings).


- transaction report-full-rpc-error <true|false> (default false)

  Enable this setting to get full rpc-error payload as message when error occurs (i.e. instead
  of just error-message).


- transaction filter-invalid-values <true|false> (default false)

  Filter out invalid leaf values from config before sending to NSO to avoid sync-from failure on
  for example invalid range expression.


- transaction canonicalize-idrefs <true|false> (default false)

  Canonicalize leaf values of type 'identityref' in config before sending to NSO, i.e.
  add/change prefix to global prefix in NSO.


- transaction filter-config-by-version <union> (default disable)

  Yang API version to allow (given meta-data annotations in yang models and/or injections).


- transaction get-config-no-filter <true|false> (default false)

  Perform full get-config without specifying any filter at all. This applies to operations like
  full sync-from and compare-config.


- transaction trans-id-method <enum> (default custom)

  Select the method for calculating transaction-id. Note that both 'config-hash' and
  'config-data' will exclude config according to filtering which might be in effect,
  i.e. the data used for calculating the transaction-id will be the config as it is sent
  to NSO, with or without unmodeled nodes.

  config-hash  - Use a snapshot of the running config for calculation.

  config-data  - Use a snapshot of the data of only the modeled parts of running config for
                 calculation.

  custom       - Use trans-id provided by ned, e.g. a device provided time-stamp of last change
                 or something similar.


  Either of:

    - devices device ned-settings cisco-iosxr_nc transaction use-maapi-setvalues <true|false>

      Use maapi setValues method instead of loadConfigStream to load data to NSO. This method is
      very strict. Inacurracies in the loaded configuration will throw an error.

  OR:

    - devices device ned-settings cisco-iosxr_nc transaction use-maapi-load-config-cmds <true|false>

      Use maapi loadConfigCmds method instead of loadConfigStream to load data to NSO. This
      method is more relaxed. Inaccuracies in the loaded configuration will be silently ignored.


- transaction abort-on-diff <true|false> (default false)

  Enable to detect diff immediately when config is applied (i.e. in commit/abort/revert).
  If a diff is detected an exception is thrown, having the effect in commit that the transaction
  is aborted (showing the diff). Note that this means some overhead in commit, where whole config
  needs to be retrieved from device to do compare. The feature 'abort-on-diff' is used to detect
  out-of-band changes, silently dropped config, and unknown side-effects to config (i.e. all
  causing a diff compared to expected NSO state). In fact, it's the only method which guarantees
  that the config was actually applied as desired. Due to the overhead, this setting should only
  be used during development.


- transaction filter-side-effects <true|false> (default false)

  Enable to automatically filter out side-effects when commiting config. With this feature enabled
  the NED will accumulate 'exclude filter-paths' which are used to filter out config from device
  to avoid diff when for example there are multiple nodes that represent the same data, i.e. in
  overlapping models.


- transaction filter-paths-file <string>

  File containing paths to filter out from data (config/oper/rpc-reply). Each line in the file
  is of the format '<include|exclude> <schema-path>'. If no include lines are present, it implies
  everything is included if not explicitly excluded. This can be combined with 'exclude-namespaces'.


- transaction delete-with-remove <true|false> (default false)

  Enable this setting to always use netconf operation 'remove' instead of 'delete' when deleting
  nodes with edit-config. This will have the effect that if trying to delete a node which is not
  present the operation will be ignored.


- transaction set-default-to-delete <true|false> (default true)

  Enable this setting to treat the operation 'set default' as a delete operation. By default, for
  devices that has 'with-defaults' handling 'explicit' (or lacks this capability), the behaviour of
  NSO is to send a 'set default' operation to the NED when a value which has a default value is to
  be deleted, i.e. the value is explicitly set back to its default instead of being deleted.


- transaction delete-by-set-to-default <true|false> (default false)

  Enable this setting to make the NED convert 'delete' operations to 'set to default' on nodes with
  default values. Use this option to prevent NSO from emitting delete operations on nodes that were
  not set in the from-transaction, which can happen if the configuration is deployed using the
  'replace' feature.


- transaction enable-diff-dependencies <true|false> (default false)

  Enable this setting to be able to use the 'diff-dependencies' annotations on nodes in the schema where device
  has bugs imposing ordering dependencies for certain edit operations. For more information in the annotations
  that can be used, see section 9.12 in the README.md.


- transaction enable-config-caching <true|false> (default false)

  Enable this option to allow the NED to handle configuration nodes that may disappear
  unexpectedly when other configuration changes are made on the device. If such nodes are
  removed spontaneously, it can cause NSO to become out of sync with the actual device
  configuration. When this setting is enabled, the NED will cache the affected configuration
  nodes and reinject them during all subsequent read operations, ensuring NSO remains
  synchronized with the device. Note: This feature requires the relevant schema nodes to be
  annotated with 'cache-parent-on' for it to function properly.


- transaction force-revert-diff <true|false> (default false)

  Enable this setting to force the use of an NSO calculated diff to apply when doing revert on device.
  For example to be able to use the 'delayed-commit' feature, this is necessary.


- transaction accept-module-as-prefix <true|false> (default false)

  Configures the NED config transform engines to accept XPaths and related references using the
  module name as the prefix instead of the prefix specified in the corresponding YANG file. This
  option is relevant only if the NED package was rebuilt using the 'use-module-as-prefix' option
  in the built-in NED rebuild tool.


- transaction nmda get-data enable <true|false> (default false)

  Use get-data rpc for data retrieval, if device supports it.


- transaction nmda get-data with-origin <true|false> (default false)

  Configure whether or not to include a </with-origin> tag in the get-data request. The
  with-origin setting is usually only supported for operational datastores, like ds:operational.


- transaction nmda get-data datastore <union>

  Configure datastore to be used by the get-data rpc. A value with prefix is mandatory.


- transaction nmda get-data origin-filter <union>

  Configure an origin filter to be used by the get-data rpc. A value with prefix is mandatory.
  Origin filter are usually only supported if an operational datastore like ds:operational has
  been configured.

2.1. ned-settings cisco-iosxr_nc transaction ignore-rpc-errors

---

Configure additional device errors that shall be treated as warnings (i.e. to be ignored, not aborting transaction).

- transaction ignore-rpc-errors <error>

  - error <string>

    Warning regular expression, e.g. '^.*interface.* does not exist.*$'. NOTE: please use
    lowercase letters for device warnings, except for regex keywords.

2.2. ned-settings cisco-iosxr_nc transaction extra-get-config-paths

---

This list can be used to add extra filters when sending get-config RPC to the device. For example if there is a bug in the device which makes it not include all config under certain top-nodes. The key of the list is the path to add (non-unique nodes must be prefixed with 'global' prefix, i.e. prefix from module).

- transaction extra-get-config-paths <path>

  - path <schema-path>

    Schema path to explicitly add to filter for get-config.

2.3. ned-settings cisco-iosxr_nc transaction exclude-namespaces

---

This list can be used to filter out certain namespaces from the configuration (i.e. all nodes belonging to namespaces given in this list will be dropped from the config before sent to NSO).

- transaction exclude-namespaces <ns>

  - ns <namespace>

    Namespace to exclude (i.e. as it appears in the yang module).

2.4. ned-settings cisco-iosxr_nc transaction inject-meta-data

---

Inject tailf:meta-data extension into schema at given path, used for example to trigger xml transform methods (java methods annotated with XMLTransformMethod) before xml is sent to NSO, or when editing, to device. The meta-data can also be used for other purposes in custom java code in the NED. The path supplied can even be a key-path, i.e. containg list keys within curly braces.

  For example, setting:

    transaction inject-meta-data 0 path /interfaces/interface/Ethernet{0/0}/mtu meta-data filter-by-version meta-value "VERSION > 7.0"

  Will be same as if the below yang statements would be present in the leaf mtu, but only for Ethernet0/0:

    tailf:meta-data filter-by-version {
      tailf:meta-value "VERSION > 7.0";
    }

NOTE: For more information about custom xml transforms, see section 'Custom XML transforms' in the README.md.

- transaction inject-meta-data <id> <path> <meta-data> <meta-value>

  - id <uint16>

    Id in list, not used.

  - path <schema-path|key-path>

    Schema path, or key-path (i.e. with keys in curly braces), to node where to inject
    the meta-data (non-unique nodes must be prefixed with 'global' prefix, i.e. prefix from module)

  - meta-data <string>

    Argument to tailf:meta-data as it would appear in yang.

  - meta-value <string>

    Argument to tailf:meta-value as it would appear in yang (can be left out if no meta-value
    sub-statement needed).

2.5. ned-settings cisco-iosxr_nc transaction config-replace-patterns inbound

---

Specify replace patterns to be applied to inbound XML data before it is parsed and forwarded to NSO.

- transaction config-replace-patterns inbound <pattern> <replace>

  - pattern <string>

  - replace <string>

2.6. ned-settings cisco-iosxr_nc transaction config-replace-patterns outbound

---

Specify replace patterns to be applied to outbound XML data before it is sent to the device.

- transaction config-replace-patterns outbound <pattern> <replace>

  - pattern <string>

  - replace <string>

3. ned-settings cisco-iosxr_nc connection

---

Settings related to the initial connection to the device, including the initial hand-shake (hello).

3.1. ned-settings cisco-iosxr_nc connection capabilities

---

Settings related the netconf capablities, and the discovery of supported yang modules.

- capabilities strict-model-revision-check <true|false> (default true)

  When enabled, the NED performs a strict revision check of the models published by the device.
  The advertised revision must exactly match the version built into the NED. If there is a
  mismatch, NSO will not support the model, and it will not be possible to read or write
  configuration using that model.


- capabilities defaults-mode-override <enum>

  Use this setting to override/force the 'with-defaults' handling reported to NSO,
  regardless of what the device reports. When 'trim' is forced, the NED will trim
  default values from data before sent to NSO, i.e. regardless of if the device support
  it or not it will look like it's supported and in use.

  report-all  - report-all.

  explicit    - explicit.

  trim        - trim.


- capabilities use-netconf-state <true|false> (default false)

  If this setting is enabled, and the device declares support for ietf-yang namespace
  'ietf-netconf-monitoring', the list /netconf-state/schemas/schema will be fetched from the
  device to discover available yang modules. Note, once fetched the contents will be cached in
  persistent oper data until cleared with the built-in rpc clear-cached-capabilities.


- capabilities use-modules-state <true|false> (default true)

  If this setting is enabled, and the device declares support for the netconf capability 'yang-library',
  the node /modules-state from the ietf namespace 'ietf-yang-library' will be fetched from the device
  to discover available yang modules. Note, once fetched the contents are cached in persistent oper
  data and will only be refetched if the 'module-set-id' changes on the device, or the cache is cleared
  with the built-in rpc clear-cached-capabilities.


- capabilities use-yang-library <true|false> (default true)

  If this setting is enabled, and the device declares support for the netconf capability 'yang-library'
  (version 1.1), the node /yang-library from the ietf namespace 'ietf-yang-library' will be fetched
  from the device to discover available yang modules. Note, once fetched the contents are cached in
  persistent oper data and will only be refetched if the 'content-id' changes on the device, or the
  cache is cleared with the built-in rpc clear-cached-capabilities.


- capabilities use-all-local-modules <true|false> (default false)

3.1.1. ned-settings cisco-iosxr_nc connection capabilities regex-exclude

---

List of regex patterns to use for excluding capabilities sent from device in hello, for example to exclude a capability which the device announces in hello, but which is not correctly implemented

- capabilities regex-exclude <pattern>

  - pattern <regex>

    Regular expression to match contents of capabilities for exclusion.

3.1.2. ned-settings cisco-iosxr_nc connection capabilities regex-include

---

List of regex patterns to use for including capabilities sent from device in hello. Note that when this list is non-empty, only capabilities matching any of the patterns in this list will be included

- capabilities regex-include <pattern>

  - pattern <regex>

    Regular expression to match contents of capabilities for inclusion.

3.1.3. ned-settings cisco-iosxr_nc connection capabilities inject

---

This list can be used to inject capabilities into the hello from the device, before processed and sent to NSO, for example if a capability sent from the device is invalid, it can be filtered out using 'regex-exclude', and replaced with an inject. Also if device leaves out a capability that should be present and is needed, it can be injected.

- capabilities inject <capa>

  - capa <string>

    Capability string to inject, as it would appear in the 'hello', that is the content which
    appears inside the 'capability' xml-tag, e.g 'urn:ietf:params:netconf:capability:candidate:1.0'.

3.2. ned-settings cisco-iosxr_nc connection ssh

---

Settings related to the SSH client used by the NED to connect to the device.

- ssh host-key known-hosts-file <string>

  Path to openssh formatted 'known_hosts' file containing valid host keys.


- ssh host-key public-key-file <string>

  Path to openssh formatted public (.pub) host key file.


- ssh host-key auto-fetch <true|false> (default false)

  Enable this setting to let the NED handle host-key validation internally (i.e. instead of using
  NSO's 'ssh fetch-host-keys' action). The NED will store the host-key sent on the first
  connection, after which it will verify that the host-key has not changed on subsequent connects
  (it's stored in persistent operational data store in NSO, see below for how to view and edit
  this list). This will work when connecting through a proxy as well. Please note that to enable
  host-key validation for proxy connections, enable the ned-setting 'proxy host-key-validation'.

  To view the stored known host-keys, you can for example do the below in ncs_cli:

     admin@ncs# show devices device dev-1 ned-settings cisco-iosxr_nc-oper known-host-keys
     HOST           PORT   FINGERPRINT
     -----------------------------------------------------------------------
     1.2.3.4        22     5c:aa:74:e0:4b:e2:a2:dd:67:0b:83:71:1b:24:42:fe
     127.0.0.1      10883  a8:a7:39:a2:ed:7e:b8:80:1f:94:81:70:53:59:2f:bb

  NOTE: When the host-key of a device changes and needs to be updated, it needs to be cleared in
  the persistent store first, this can for example be done from the command line with the ncs_cmd
  tool like this:

   $ ncs_cmd -c "mdel /ncs:devices/device{dev-1}/ned-settings/cisco-iosxr_nc-oper/known-host-keys"


- ssh auth-key private-key-file <string>

  Path to openssh formatted private key file for doing public key auth to device or proxy. Note
  that if private-key authentication is needed to the device when connecting through a proxy,
  that needs to be configured in 'proxy/auth-key/private-key-file.


- ssh keep-alive-interval <seconds> (default 0)

  Configure SSH client keep alive interval in seconds, default 0 (i.e. no keep-alive). The
  keep-alive is implemented in the client by sending an ssh 'ignore' message on the given
  interval.

4. ned-settings cisco-iosxr_nc proxy

---

Configure NED to access device via an ssh proxy (i.e. a ssh 'jump-host'). By default, when this options is used, the address, port, and credentials normally given for the device in NSO, is used as the address and credentials for the ssh proxy, in which case the ned-settings here are then used to access the actual device.

This 'reverse' logic is the effect of how the API historically worked, and can be changed by enabling the setting 'global-proxy'. When this setting is set to true, the device config is the address/port and credentials for the actual device (behind the proxy), and the proxy host is configured in this section. This means that the proxy can be configured globally, or in a profile, which is a convenient way to switch all or some devices to connect through a jump-host.

- proxy global-proxy <true|false> (default false)

  Enable this setting to 'reverse' the meaning of the settings in the proxy section into actually configuring the
  proxy host instead of the device behind the proxy. Note that if enabling 'global-proxy' and host-key-validation is
  preferred, the host-key of the proxy either needs to be added in the ned setting 'connection/ssh/host-key', or be
  added to the .ssh/known_hosts of the user running NSO, or 'ssh host-key auto-fetch' needs to be enabled. The NSO
  built-in standard fetch-host-keys can not be used of course since the configured device address is not to the proxy any more.


- proxy remote-address <ip-address|domain-name>

  Internal address of device, i.e. when accessed from the proxy.


- proxy remote-port <uint16>

  Port of device.


  Either of:

    - devices device ned-settings cisco-iosxr_nc proxy remote-name <string>

      User name on the device behind the proxy.

    - devices device ned-settings cisco-iosxr_nc proxy remote-password <string>

      Password on the device behind the proxy.

  OR:

    - devices device ned-settings cisco-iosxr_nc proxy authgroup <string>

      Authentication credentials for the device behind the proxy.


- proxy auth-key private-key-file <string>

  Path to openssh formatted private key file for doing public key auth to device behind proxy.
  Note that if private-key authentication is needed to the proxy itself, that needs to be
  configured as it would be for the device, in 'connection/ssh/auth-key/private-key-file.


- proxy host-key-validation <true|false> (default false)

  Determines if the host-key of the device or proxy should be validated or not. If validation is
  preferred, the host-key must be configured in 'connection/ssh/host-key'.

5. ned-settings cisco-iosxr_nc live-status

---

Configure NED settings related to live-status.

- live-status do-separate-get-calls <true|false> (default false)

  By default this NED is passing a subtree filter with all requested paths to the device in one
  get call. This is a fast method. Some devices do however not function properly with subtree
  filters. In this case it is necessary to do one separate get call for each requested path. Set
  to true if the NED shall do separate get calls.


- live-status show-stats-filter <true|false> (default true)

  Use the filter API from NSO to do live-status requests (available in NSO 6.1 and later). This
  API is much more flexible and will result in fewer round-trips to the device and possibly less
  data transferred from the device.


- live-status time-to-live <int32> (default 50)

  Define time-to-live for data fetched from the device via live-status.


- live-status filter-unmodeled <true|false> (default true)

  Filters out operational data not present in yang-model before returning result to NSO.


- live-status filter-invalid-values <true|false> (default false)

  Filter out invalid leaf values from config before sending to NSO to avoid sync-from failure on
  for example invalid range expression.


- live-status canonicalize-idrefs <true|false> (default true)

  Canonicalize leaf values of type 'identityref' in operational data before sending to NSO, i.e.
  add/change prefix to global prefix in NSO.


- live-status nmda get-data enable <true|false> (default false)

  Use get-data rpc for data retrieval, if device supports it.


- live-status nmda get-data with-origin <true|false> (default false)

  Configure whether or not to include a </with-origin> tag in the get-data request. The
  with-origin setting is usually only supported for operational datastores, like ds:operational.


- live-status nmda get-data datastore <union> (default operational)

  Configure datastore to be used by the get-data rpc. A value with prefix is mandatory.


- live-status nmda get-data origin-filter <union>

  Configure an origin filter to be used by the get-data rpc. A value with prefix is mandatory.
  Origin filter are usually only supported if an operational datastore like ds:operational has
  been configured.


- live-status nmda get-data skip-config <true|false> (default false)

  Ask the device to not include 'config true' data in the response.

5.1. ned-settings cisco-iosxr_nc live-status regex-exclude

---

This list of regular expressions match the schema path of nodes to filter out from live-status (oper) data before sending it to NSO. The regex matches on either of the pure tag-path, 'global' path, or the key-path (i.e. possibly including keys within curly braces) of nodes in the data. I.e. if a path is unique, prefixes can be omitted, but not when used in a key-path, then a 'global' path is needed, i.e. prefixed as it would appear in NSO, including the prefix on each level where new namespace occurs.

- live-status regex-exclude <pattern>

  - pattern <regex>

    Regular expression matching path/key-path of node(s) to exclude.

5.2. ned-settings cisco-iosxr_nc live-status cli

---

Configuration of CLI interaction through 'exec any '.

- cli port <uint16>

  Alternatative port on device, if interactive CLI not availble on same port as 'netconf'
  subsystem.


- cli prompt-pattern <string> (default \A[a-zA-Z0-9][^\# ]+# ?$)

  Regex to match device prompt.


- cli no-pagination-cmd <string> (default terminal length 0)

  Command line to send after login to turn off pagination on the  device (i.e. to make output from commands not
  stop to prompt user for 'more').

5.2.1. ned-settings cisco-iosxr_nc live-status cli auto-prompts

---

Sometimes when entering commands in an interative shell, the device prompts for some specific input, in cases like this, this list can be configured with pairs of "questions" and "answers" to be used when interacting with the device. The "questions" are in the form of regular-expressions, which matches the prompt or "question" output from the device, and the "answers" are the string to send back to the device, when that specific "question" is found in the output from the device.

For example, to add the response "secret" for a password prompt, one can add the below ned-settings:

live-status cli auto-prompts 10 question ".*assword: ?" answer secret

- cli auto-prompts <id> <question> <answer>

  - id <WORD>

    List id, any string (NOTE: list is matched in the order sorted on id).

  - question <WORD>

    Device question, as a regular expression.

  - answer <WORD>

    Answer to device question, i.e verbatim string to send as answer when 'question' is matched.

6. ned-settings cisco-iosxr_nc logger

---

Settings for controlling logs generated.

- logger level <enum> (default info)

  Sets the logger verbosity. Enable raw trace on the device instance in NSO to
  get trace output. To trace the netconf raw RPCs, set level to verbose or debug.

  error    - Most restricitve level, only log errors.

  info     - Normal level, logs errors and important events.

  verbose  - Intermediate debug level, logs most events.

  debug    - Least restrictive level, logs everything, output might grow very large.


- logger java <true|false> (default true)

  Toggle logs to be added to ncs-java-vm.log, Note, this file is shared between all NED
  instances and might grow very large if level is increased.

7. ned-settings cisco-iosxr_nc developer

---

Contains settings used by the NED developers.

- developer trace-timestamp <true|false> (default false)

  Add timestamp from NED instance in trace messages for debug purpose.


- developer sync-from-verbose <enum> (default brief)

  Set info level for sync-from verbose output.

  brief  - brief.

  full   - full.


- developer strict-maapi-error-check <true|false> (default true)

  When this setting is enabled, if maapi reports error when loading data to NSO, the error is
  reported back to NSO, failing show operation.


- developer progress-verbosity <enum> (default debug)

  Maximum NED verbosity level which will get written in devel.log file.

  disabled      - disabled.

  normal        - normal.

  verbose       - verbose.

  very-verbose  - very-verbose.

  debug         - debug.


- developer platform model <string>

  Override device model name/number.


- developer platform name <string>

  Override device name.


- developer platform version <string>

  Override device version.